Comments for Voltriderz

Comment on Bafang Rear Hub Motors: Best Models & Expert Reviews (2026) by Glenn McKeon

Glenn McKeon — Mon, 07 Oct 2024 14:30:44 +0000

The Bafang H640 does not have “quiet operation” as stated above, at least on my ebike. It is LOUD and makes my otherwise fairly refined bike sound a bit chintzy…

Comment on Tongsheng TSDZ8 Conversion: Complete Installation Guide by Jay

Jay — Thu, 03 Oct 2024 18:52:42 +0000

How do you connect a light to this set-up and how do you update the motor firmware?

Comment on Bafang M400 Review: The Smooth 250W Mid-Drive Motor by TRANHA

TRANHA — Sat, 14 Sep 2024 15:24:42 +0000

Hi, I’m using a bafang m400 36v250w motor but it has a code error. Can you give me the codes to reset it?

Comment on Top 7 Worst Bafang Motor Problems & How To Fix Them by mark bowden

mark bowden — Mon, 01 Jan 2024 15:14:26 +0000

I have the M600 motor on a 29er MTB. At 5000 kms the main bearing was replaced, now at 6500 the noise from the motor is embarrassing and seems failure is eminent, however it still performs well.
I would like to send a video of the noise its making….

Comment on Top 7 Worst Bafang Motor Problems & How To Fix Them by Robert Nichols

Robert Nichols — Fri, 29 Dec 2023 15:57:56 +0000

I’m a little concerned about buying another bafang mid drive, my bbs02 died after only 6 miles. The stator & rotor was found to have overheated. I was using a greenlance 48v 17ah battery & I was riding on the flat, it was November so the ambient temperature had nothing to do with its failure. I’m a mature cyclist & fully understand the limitations of these motors, not overstretching or constant use of throttle.

Comment on Top 7 Worst Bafang Motor Problems & How To Fix Them by ian

ian — Fri, 15 Dec 2023 20:17:38 +0000

hi, i have a m200 that has power loss when pushed ,would like to get firmware update but can’t find a bike shop to touch it (east midlands gb) can anybody point me in right direction

Comment on Top 7 Worst Bafang Motor Problems & How To Fix Them by James Lutz

James Lutz — Tue, 12 Dec 2023 02:16:47 +0000

I purchased a Bafang hub motor, I had to order an extension 3 pin male/female cord. This hub motor is on a Sunseeker trike. I’m getting an er 8 code. What’s wrong?

Comment on Top 7 Worst Bafang Motor Problems & How To Fix Them by David Cunningham

David Cunningham — Tue, 14 Nov 2023 20:47:55 +0000

I am getting a code21H. Speed sensor malfunction. Is this simply a matter of putting in a new speed sensor? Is this a common problem?

Comment on Bafang Mid-Drive Motor: Complete Installation Guide 🔧 by James Lutz

James Lutz — Wed, 01 Nov 2023 20:15:44 +0000

I purchased a Bafang motor kit and installed it on a SUN recumbent trike. The front wheel is 16″ and maybe it is set for being a 26″ therefore my speed is not accurate. also it is registering in k/ph.
How do I change my settings? I tried watching u-tube and they go to fast for me. Is there a diagram or picture of the 0n/off switch so I can comprehend it better.
Sincerely,
James Lutz

Comment on Top 7 Worst Bafang Motor Problems & How To Fix Them by Jim Harrison

Jim Harrison — Wed, 01 Nov 2023 17:00:07 +0000

Our motor is not working and we have a flashing wrench on the display. Any idea what might be wrong? Battery shows full.
Thanks, Jim